1 / 5
Model No. : | IG7 |
---|---|
Brand Name : | ブランド |
製品説明
4Cyl IG7ダコタナバホインジェクターレールLPG CNG
2オーム4気筒IG7ダコタRAILタイプ鉄道インジェクタ の特徴を 次のように:
1.ガス状LPGおよび天然ガス用のレールインジェクター。
2. 0.47 mmストロークのシングルバージョン。
3.アンプと互換性のある2ウェイ内蔵防水コネクタ付きコイル。
4. アルミニウムのボディ。
5.速度と持続時間の点で高性能を達成するのに適した建築技術。
6.ほこりの蓄積にあまり敏感ではありません。
7.高い内部流れの安定性と反復性 。
2オーム4シリンダーIG7ダコタナバホレールインジェクターの全体寸法:
レールタイプIG7ダコタLpg / Cngインジェクターレールの技術的パラメーター:
Characteristic | Unit | Value | Note |
Injector Version | N° of cylinders | 2, 3, 4 |
|
Material body and treatment |
|
Aluminum | |
Relative Pressure | Bar (Psi) | From 0.5 to 2.0 (7 to 29) | Working pressure |
4.5 (65) | Max pressure | ||
Rated voltage (at coil) | Volt | 10.8 - 14.4 |
|
Coil type | by encoding | E2 |
|
Resistance | Q | 2 | ± 5% at T= 25° |
Suggested peak current time (duration) | ms | 2.4 |
|
Suggested holding current (±10%) | A | 1.4 |
|
Cold Starting Requirements |
|
Increase up to 20% the "peak current time" for first cycles when gas temperature is < 10°C | |
Complete OPENING Response Time | ms | 1.7 | (±10% - total injection time 5 ms) ± 5% tested without nozzle at 14V Dp=1bar T= 25°C |
Complete CLOSING Response Time | ms | 1.4 |
|
Minimum injection pulse | ms | 1.8 | tested with 2 mm nozzle diameter at 14V Ap=1 bar T= 25°C |
Stroke | Micron | 470 |
|
Seat Diameter | mm | 3.3 |
|
Static flow rate (with max nozzle O) for 1 single injector at 20°C (with air) | SLPM (sL/min) | 115 | at 1 bar inlet pressure |
170 | at 2 bar inlet pressure | ||
Leakage (tested with air) | cc/h | < 15 |
|
Noise level | dB | T.B.D | ±1 dB Rail Test Condition |
Compatibility with gas |
|
LPG, CNG |
|
Driver Stage |
|
Peak and Hold (PWM) |
|
Coil Connector type |
|
2 way Amp super seal fermale connector with tab contacts | About connecting wire, refer to our drawing, code 114.01.AMP.001 |
Inlet gas fitting for rubber hose | mm | φ10 mm, φ12 mm, φ14 mm, φ16 mm | |
Outlet gas fitting |
|
Calibrated nozzles M8x1 for rubber hose φ4 mm - φ5 mm - φ6 mm | |
Calibrated hole φ range (for nozzles) | φ | From 1.00 to 3.25 mm (0.25 mm step) |
|
Approvals |
|
110R-00 67R-01 (-40°C to +120°C) |
|
Principle of operation |
|
Solenoid valve, Normally closed, Mobile Plunger | |
Power handling capability LPG | HP/cyl | 1 bar up to 40 HP/cyl | |
Power handling capability CNG | HP/cyl | 2 bar up to 35 HP/cyl | |
Coil IP Rating |
|
IP54 |
|
レールタイプ2オーム4シリンダーIG7ダコタレールインジェクターのパッキングショー:
使用方法:
1.空気漏れの不純物を効果的に通過させるために、スプレーレールのインジェクションパイプの前端にフィルターを取り付けることをお勧めします。
不純物や微粒子がレールレールに入らないようにし、3か月または20,000キロメートルフィルターを交換します。
2.最大限の使用を確保するために、レールをできるだけ垂直角度で設置することをお勧めします。
3.スプレーレールのさまざまなモデルに応じて、電気制御設定で対応するスプレーレールタイプを選択する必要があります。
4.エンジンの出力に応じて、適切なノズル直径を選択する必要があります。
あなたの要求に焦点を当て、あなたに最高のソリューションを提供します:
√疑問点がある場合はご連絡ください
√どこかで変更が必要な場合はご連絡ください
√探しているものでない場合は、お問い合わせください
√設計を行う場合はお問い合わせください
ご質問やお問い合わせへようこそ!
このサプライヤーにお問い合わせを送ってください